configure network interface
ifconfig utility is used to assign an
address to a network interface and/or configure network interface
parameters. Generally speaking,
hostname.if(5) files are used at boot-time to define the
network address of each interface present on a machine;
ifconfig is used at a later time to redefine an
interface's address or other operating parameters.
ifconfig displays the current
configuration for a network interface when no optional parameters are
supplied. If a protocol family is specified,
ifconfig will report only the details specific to
that protocol family. If no parameters are provided, a summary of all
interfaces is provided.
Only the superuser may modify the configuration of a network interface.
The following options are available:
- Causes full interface alias information for each interface to be displayed.
ifconfigto print information on all interfaces. The protocol family may be specified as well. This is the default, if no parameters are given to
- Print the names of all network pseudo-devices that can be created
dynamically at runtime using
- The interface parameter is a string of the form “name unit”, for example, “en0”. If no optional parameters are supplied, this string can instead be just “name”. If an interface group of that name exists, all interfaces in the group will be shown. Otherwise all interfaces of the same type will be displayed (for example, “fxp” will display all fxp(4) interfaces).
- Specifies the address family which affects interpretation of the remaining parameters. Since an interface can receive transmissions in differing protocols with different naming schemes, specifying the address family is recommended. The address or protocol families currently supported are “inet” and “inet6”.
- Internet version 4 and 6 addresses take the form of a host name present in the host name database, hosts(5); “dot” notation (IPv4); colon separated (IPv6); or CIDR notation.
- Specify the address of the correspondent on the other end of a point-to-point link.
The following parameters may be set with
- Establish an additional network address for this interface. This is sometimes useful when changing network numbers, and one wishes to accept packets addressed to the old interface.
- A synonym for
delete. Use of this option is discouraged in favour of
- Enable the use of the Address Resolution Protocol (ARP) in mapping between network level addresses and link level addresses (default). This is currently implemented for mapping between DARPA Internet addresses and Ethernet addresses.
- Disable the use of ARP.
- Enable autoconfiguration. Valid for “inet6” only. If
autoconfis enabled router advertisements are accepted on this interface and the kernel sends periodic router solicitations from this interface.
- Disable autoconfiguration.
- (inet only) Specify the address to use to represent broadcasts to the network. The default broadcast address is the address with a host part of all 1's.
- Create the specified network pseudo-device. At least the following devices
can be created on demand:
bridge(4), carp(4), enc(4), gif(4), gre(4), lo(4), mpe(4), mpw(4), pflog(4), pflow(4), pfsync(4), ppp(4), pppoe(4), trunk(4), tun(4), vether(4), vlan(4)
- Enable driver-dependent debugging code; usually, this turns on extra console error logging.
- Disable driver-dependent debugging code.
- Remove the default inet address associated with the interface, including any netmask or destination address configured with it. An address and address family can be given to make the deletion more specific.
- Specify a description of the interface. This can be used to label interfaces in situations where they may otherwise be difficult to distinguish.
- Clear the interface description.
- Destroy the specified network pseudo-device.
- Mark an interface “down”. When an interface is marked “down”, the system will not attempt to transmit messages through that interface. If possible, the interface will be reset to disable reception as well. This action automatically disables routes using the interface.
- Assign the interface to a “group”.
group-name may not be longer than 15 characters and
must not end with a digit. Any interface can be in multiple groups.
For instance, a group could be used to create a hardware independent pf(4) ruleset (i.e. not one based on the names of NICs) using existing (egress, carp, etc.) or user-defined groups.
Some interfaces belong to specific groups by default:
- All interfaces are members of the all interface group.
- Cloned interfaces are members of their interface family group. For example, a PPP interface such as ppp0 is a member of the ppp interface family group.
- pppx(4) interfaces are members of the pppx interface group.
- The interface(s) the default route(s) point to are members of the egress interface group.
- IEEE 802.11 wireless interfaces are members of the wlan interface group.
- Any interfaces used for network booting are members of the netboot interface group.
- Remove the interface from the given “group”.
- Display the interface hardware features:
- The device supports IPv4 checksum offload.
- As above, for TCP in IPv4 datagrams.
- As above, for UDP.
- The device can handle full sized frames, plus the size of the vlan(4) tag.
- On transmit, the device can add the vlan(4) tag.
- As CSUM_TCPv4, but supports IPv6 datagrams.
- As above, for UDP.
- The device supports Wake on LAN (WoL).
- The maximum MTU supported.
- Remove all configured inet(4) addresses on the given interface.
- Disable inet6(4) on the given interface and remove all configured inet6(4) addresses, including the link-local ones. This is the default. To turn inet6 on, use eui64, use autoconf or assign any inet6 address.
- Set the media instance to minst. This is useful for devices which have multiple physical layer interfaces (PHYs). Setting the instance on such devices may not be strictly required by the network interface driver as the driver may take care of this automatically; see the driver's manual page for more information.
- Enable special processing of the link level of the interface. These three options are interface specific in actual effect; however, they are in general used to select special modes of operation. An example of this is to select the connector type for some Ethernet cards. Refer to the man page for the specific driver for more information.
- Disable special processing at the link level with the specified interface.
- Change the link layer address (MAC address) of the interface. This should be specified as six colon-separated hex values, or can be chosen randomly.
- Set the media type of the interface to type. If no
argument is given, display a list of all available media.
Some interfaces support the mutually exclusive use of one of several different physical media connectors. For example, a 10Mb/s Ethernet interface might support the use of either AUI or twisted pair connectors. Setting the media type to “10base5” or “AUI” would change the currently active connector to the AUI port. Setting it to “10baseT” or “UTP” would activate twisted pair. Refer to the interface's driver-specific man page for a complete list of the available types, or use the following command for a listing of choices:
$ ifconfig interface media
- Set the specified media options on the interface.
opts is a comma delimited list of options to apply
to the interface. Refer to the interface's driver-specific man page for a
complete list of available options, or use the following command for a
listing of choices:
$ ifconfig interface media
- Disable the specified media options on the interface.
- Set the routing metric of the interface to nhops, default 0. The routing metric can be used by routing protocols. Higher metrics have the effect of making a route less favorable.
- If the driver for the interface supports the media selection system, set the specified operating mode on the interface to the given mode. For IEEE 802.11 wireless interfaces that support multiple operating modes, this directive is used to select between 802.11a (“11a”), 802.11b (“11b”), and 802.11g (“11g”) operating modes.
- Enable Multiprotocol Label Switching (MPLS) on the interface, allowing it to send and receive MPLS traffic.
- Disable MPLS on the interface.
- Set the MTU for this device to the given value.
Cloned routes inherit this value as a default. For Ethernet devices which
support setting the MTU, a value greater than 1500 enables jumbo frames.
The hardmtu output from
hwfeaturesshows the maximum supported MTU.
- (inet and inet6) Specify how much of the address to reserve for subdividing networks into subnetworks. The mask includes the network part of the local address and the subnet part, which is taken from the host field of the address. The mask can be specified as a single hexadecimal number with a leading 0x, with a dot-notation Internet address, or with a pseudo-network name listed in the network table networks(5). The mask contains 1's for the bit positions in the 32-bit address which are to be used for the network and subnet parts, and 0's for the host part. The mask should contain at least the standard network portion, and the subnet field should be contiguous with the network portion.
- (inet and inet6 only) Effect is similar to
netmask, but you can specify prefix length by digits.
- Set the interface routing priority to n. This will influence the default routing priority of new static routes added to the kernel. n is in the range of 0 to 15 with smaller numbers being better.
- Attach the interface to the routing domain with the specified rdomainid. Interfaces in different routing domains are separated and can not directly pass traffic between each other. It is therefore possible to reuse the same addresses in different routing domains. If the specified rdomain does not yet exist it will be created, including a routing table with the same id. By default all interfaces belong to routing domain 0.
- (inet) Attach route-label to new network routes of the specified interface. Route labels can be used to implement policy routing; see route(4), route(8), and pf.conf(5).
- Clear the route label.
- Set the timeslot range map, which is used to control which channels an interface device uses.
- Mark an interface “up”. This may be used to enable an
interface after an
ifconfig down. It happens automatically when setting the first address on an interface. If the interface was reset when previously marked down, the hardware will be re-initialized.
- Enable Wake on LAN (WoL). When enabled, reception of a WoL frame will cause the network card to power up the system from standby or suspend mode. WoL frames are sent using arp(8).
- Disable WoL. WoL is disabled at boot by the driver, if possible.
ifconfig supports a multitude of
sub-types, described in the following sections:
The following options are available for a bridge(4) interface:
- Add interface as a member of the bridge. The interface is put into promiscuous mode so that it can receive every packet sent on the network. An interface can be a member of at most one bridge.
- Display the addresses that have been learned by the bridge.
- Add interface as a span port on the bridge.
- Automatically detect the spanning tree edge port status on interface. This is the default for interfaces added to the bridge.
- Disable automatic spanning tree edge port detection on interface.
- Automatically detect the point-to-point status on interface by checking the full duplex link status. This is the default for interfaces added to the bridge.
- Disable automatic point-to-point link detection on interface.
- Mark interface so that no non-IPv4, IPv6, ARP, or Reverse ARP packets are accepted from it or forwarded to it from other bridge member interfaces.
- Allow non-IPv4, IPv6, ARP, or Reverse ARP packets through interface.
- Remove interface from the bridge. Promiscuous mode is turned off for the interface when it is removed from the bridge.
- Delete address from the cache.
- Delete interface from the list of span ports of the bridge.
- Mark interface so that packets are sent out of the interface if the destination port of the packet is unknown. If the bridge has no address cache entry for the destination of a packet, meaning that there is no static entry and no dynamically learned entry for the destination, the bridge will forward the packet to all member interfaces that have this flag set. This is the default for interfaces added to the bridge.
- Mark interface so that packets are not sent out of the interface if the destination port of the packet is unknown. Turning this flag off means that the bridge will not send packets out of this interface unless the packet is a broadcast packet, multicast packet, or a packet with a destination address found on the interface's segment. This, in combination with static address cache entries, prevents potentially sensitive packets from being sent on segments that have no need to see the packet.
- Stop the bridge from forwarding packets.
- Set interface as a spanning tree edge port. An edge port is a single connection to the network and cannot create bridge loops. This allows a straight transition to forwarding.
- Disable edge port status on interface.
- Remove all dynamically learned addresses from the cache.
- Remove all addresses from the cache including static addresses.
- Remove all Ethernet MAC filtering rules from interface.
- Set the time (in seconds) before an interface begins forwarding packets. Defaults to 15 seconds, minimum of 4, maximum of 30.
- Set the time (in seconds) between broadcasting spanning tree protocol
configuration packets. Defaults to 2 seconds, minimum of 1, maximum of 2.
This option is only supported in STP mode with rapid transitions disabled;
protocommand for setting the protocol version.
- Set the transmit hold count, which is the number of spanning tree protocol packets transmitted before being rate limited. Defaults to 6, minimum of 1, maximum of 10.
- Set the spanning tree path cost of interface to num. Defaults to 55, minimum of 1, maximum of 200000000 in RSTP mode, and maximum of 65535 in STP mode.
- Automatically calculate the spanning tree priority of interface based on the current link speed, interface status, and spanning tree mode. This is the default for interfaces added to the bridge.
- Set the spanning tree priority of interface to num. Defaults to 128, minimum of 0, maximum of 240.
- Mark interface so that the source address of packets received from the interface are entered into the address cache. This is the default for interfaces added to the bridge.
- Mark interface so that the source address of packets received from interface are not entered into the address cache.
- Setting this flag stops all IP multicast packets from being forwarded by the bridge.
- Clear the
link0flag on the bridge interface.
- Setting this flag stops all non-IP multicast packets from being forwarded by the bridge.
- Clear the
link1flag on the bridge interface.
- Setting this flag causes all packets to be passed on to ipsec(4) for processing, based on the policies established by the administrator using the ipsecctl(8) command and ipsec.conf(5). If appropriate security associations (SAs) exist, they will be used to encrypt or decrypt the packets. Otherwise, any key management daemons such as isakmpd(8) that are running on the bridge will be invoked to establish the necessary SAs. These daemons have to be configured as if they were running on the host whose traffic they are protecting (i.e. they need to have the appropriate authentication and authorization material, such as keys and certificates, to impersonate the protected host(s)).
- Clear the
link2flag on the bridge interface.
- Set the address cache size to size. The default is 100 entries.
- Set the time (in seconds) that a spanning tree protocol configuration is valid. Defaults to 20 seconds, minimum of 6, maximum of 40.
- Force the spanning tree protocol version. The available values are rstp to operate in the default Rapid Spanning Tree (RSTP) mode or stp to force operation in Spanning Tree (STP) mode with rapid transitions disabled.
- Set interface as a point-to-point link. This is required for straight transitions to forwarding and should be enabled for a full duplex link or a trunk(4) with at least two physical links to the same network segment.
- Disable point-to-point link status on interface. This should be disabled for a half duplex link and for an interface connected to a shared network segment, like a hub or a wireless network.
- Add a filtering rule to an interface. Rules have a similar syntax to those in pf.conf(5). Rules can be used to selectively block or pass frames based on Ethernet MAC addresses. They can also tag packets for pf(4) to filter on. Rules are processed in the order in which they were added to the interface, and the first rule matched takes the action (block or pass) and, if given, the tag of the rule. If no source or destination address is specified, the rule will match all frames (good for creating a catchall policy).
- Load a set of rules from the file filename.
- Display the active filtering rules in use on interface.
- Set the spanning priority of this bridge to num. Defaults to 32768, minimum of 0, maximum of 61440.
- Add a static entry into the address cache pointing to interface. Static entries are never aged out of the cache or replaced, even if the address is seen on a different interface.
- Enable spanning tree protocol on interface.
- Disable spanning tree protocol on interface. This is the default for interfaces added to the bridge.
- Set the timeout, in seconds, for addresses in the cache to time. The default is 240 seconds. If time is set to zero, then entries will not be expired.
- Start the bridge forwarding packets.
The following options are available for a carp(4) interface:
- Set the base advertisement interval to n seconds. Acceptable values are 0 to 254; the default value is 1 second.
- Skew the advertisement interval by n. Acceptable values are 0 to 254; the default value is 0.
- Set the load balancing mode to mode. Valid modes are arp, ip, ip-stealth, and ip-unicast.
- Create a load balancing group consisting of up to 32 nodes. Each node is specified as a vhid:advskew tuple in a comma separated list.
- Attach to parent interface iface.
- Send the carp advertisements to a specified point-to-point peer or multicast group instead of sending the messages to the default carp multicast group. The peer_address is the IP address of the other host taking part in the carp cluster. With this option, carp(4) traffic can be protected using ipsec(4) and it may be desired in networks that do not allow or have problems with IPv4 multicast traffic.
- Send the advertisements to the default carp multicast group.
- Set the authentication key to passphrase. There is no passphrase by default.
- Explicitly force the interface to enter this state. Valid states are init, backup, and master.
- Set the virtual host ID to n. Acceptable values are 1 to 255.
Taken together, the
advskew indicate how frequently, in seconds, the
host will advertise the fact that it considers itself master of the virtual
host. The formula is
advskew / 256). If the master does not advertise
within three times this interval, this host will begin advertising as
IEEE 802.11 (WIRELESS DEVICES)
The following options are available for a wireless interface:
- Set the desired BSSID.
- Unset the desired BSSID. The interface will automatically select a BSSID in this mode, which is the default.
- Set the channel (radio frequency) to n.
With no channel specified, show the list of channels supported by the device.
- Unset the desired channel. It doesn't affect the channel to be created for IBSS or Host AP mode.
- Set specified flag. The flag name can be either
hidenwid’ or ‘
nobridge’. The ‘
hidenwid’ flag will hide the network ID (ESSID) in beacon frames when operating in Host AP mode. It will also prevent responses to probe requests with an unspecified network ID. The ‘
nobridge’ flag will disable the direct bridging of frames between associated nodes when operating in Host AP mode. Setting this flag will block and filter direct inter-station communications.
Note that the ‘
hidenwid’ and ‘
nobridge’ options do not provide any security. The hidden network ID will be sent in clear text by associating stations and can be easily discovered with tools like tcpdump(8) and hostapd(8).
- Remove specified flag.
- Configure network ID. The id can either be any text string up to 32 characters in length, or a series of hexadecimal digits up to 64 digits. The empty string allows the interface to connect to any available access points. Note that network ID is synonymous with Extended Service Set ID (ESSID).
- Set the network ID to the empty string to allow the interface to connect to any available access point.
- Enable WEP encryption using the specified key. The
key can either be a string, a series of hexadecimal
digits (preceded by ‘0x’), or a set of keys of the form
“n:k1,k2,k3,k4” where ‘n’ specifies which of
the keys will be used for transmitted packets, and the four keys,
“k1” through “k4”, are configured as WEP keys.
If a set of keys is specified, a comma (‘,’) within the key
must be escaped with a backslash. Note that if multiple keys are used,
their order must be the same within the network.
The length of each key must be either 40 bits for 64-bit encryption (5-character ASCII string or 10 hexadecimal digits) or 104 bits for 128-bit encryption (13-character ASCII string or 26 hexadecimal digits).
- Disable WEP encryption.
- Enable WEP encryption using the persistent key stored in the network card.
- Write key to the persistent memory of the network card, and enable WEP encryption using that key.
- Enable 802.11 power saving mode. Optionally set the receiver sleep duration (in milliseconds).
- Disable 802.11 power saving mode.
- Show the results of an access point scan. In Host AP mode, this will dump the list of known nodes without scanning.
- Set the transmit power. The driver will disable any auto level and transmit power controls in this mode.
- Disable manual transmit power mode and enable any auto level and transmit power controls.
- Enable Wi-Fi Protected Access. WPA is a Wi-Fi Alliance protocol based on the IEEE 802.11i standard. It was designed to enhance the security of wireless networks. Notice that not all drivers support WPA. Check the driver's manual page to know if this option is supported.
- Disable Wi-Fi Protected Access.
- Set the comma-separated list of allowed authentication and key management
The supported values are “psk” and “802.1x”. psk authentication (also known as personal mode) uses a 256-bit pre-shared key. 802.1x authentication (also known as enterprise mode) is used with an external IEEE 802.1X authentication server, such as wpa_supplicant. The default value is “psk”. “psk” can only be used if a pre-shared key is configured using the
- Set the comma-separated list of allowed pairwise ciphers.
The supported values are “tkip”, “ccmp”, and “usegroup”. usegroup specifies that no pairwise ciphers are supported and that only group keys should be used. The default value is “tkip,ccmp”. If multiple pairwise ciphers are specified, the pairwise cipher will be negotiated between the station and the access point at association time. A station will always try to use ccmp over tkip if both ciphers are allowed and supported by the access point. If the selected cipher is not supported by the hardware, software encryption will be used. Check the driver's manual page to know which ciphers are supported in hardware.
- Set the group cipher used to encrypt broadcast and multicast traffic.
The supported values are “wep40”, “wep104”, “tkip”, and “ccmp”. The default value is “tkip”. The use of wep40 or wep104 as the group cipher is discouraged due to weaknesses in WEP. The
wpagroupcipheroption is available in Host AP mode only. A station will always use the group cipher of the BSS.
wpakeypassphrase | hexkey
- Set the WPA key and enable WPA. The key can be given using either a
passphrase or a full length hex key, starting with 0x. If a passphrase is
nwidoption must be set prior to specifying the
ifconfigwill hash the nwid along with the passphrase to create the key.
- Delete the pre-shared WPA key and disable WPA.
- Set the comma-separated list of allowed WPA protocol versions.
The supported values are “wpa1” and “wpa2”. wpa1 is based on draft 3 of the IEEE 802.11i standard whereas wpa2 is based on the ratified standard. The default value is “wpa1,wpa2”. If “wpa1,wpa2” is specified, a station will always use the wpa2 protocol when supported by the access point.
The following options are available for an ip6(4) interface:
- Set the IPv6 anycast address bit.
- Clear the IPv6 anycast address bit.
- Enable privacy extensions for stateless IPv6 address autoconfiguration
(RFC 4941) on the interface. The purpose of these extensions is to prevent
tracking of individual devices which connect to the IPv6 internet from
different networks using stateless autoconfiguration. The interface
identifier often remains constant and provides the lower 64 bits of an
autoconfigured IPv6 address, facilitating tracking of individual devices
(and hence, potentially, users of these devices) over long periods of time
(weeks to months to years). When these extensions are active, random
interface identifiers are used for autoconfigured addresses.
Autoconfigured addresses are also made temporary, which means that they will automatically be replaced regularly. Temporary addresses are deprecated after 24 hours. Once a temporary address has been deprecated, a new temporary address will be configured upon reception of a router advertisement indicating that the prefix is still valid. Deprecated addresses will not be used for new connections as long as a non-deprecated address remains available. Temporary addresses become invalid after one week, at which time they will be removed from the interface. Address lifetime extension through router advertisements is ignored for temporary addresses.
- Disable IPv6 autoconf privacy extensions on the interface. Currently configured addresses will not be removed until they become invalid.
- Fill the interface index (the lowermost 64th bit of an IPv6 address) automatically.
- Set preferred lifetime for the address.
- Set the IPv6 tentative address bit.
- Clear the IPv6 tentative address bit.
- Set valid lifetime for the address.
The following options are available for interface groups:
- Specify the group.
- Increase carp(4) demote count for given interface group by number. Acceptable values are 0 to 128. If number is omitted, it is increased by 1. Demote count can be set up to 255.
- Decrease carp(4) demote count for given interface group by number. Acceptable values are 0 to 128. If number is omitted, it is decreased by 1.
The following options are available for an mpe(4) interface:
- Set the MPLS label to mpls-label. This value is a 20-bit number which will be used as the MPLS header for packets entering the MPLS domain.
The following options are available for an mpw(4) interface:
- Configure the mpw interface to use control-word.
- Remove control-word configuration from the interface.
- Configures the mpw encapsulation type with value
encapsulation which can be
ethernet-tagged. By default it's assumed to be
- Set mpw local label to local-label and remote label to remote-label. The local-label is a 20-bit number which will be used to create a local label route to the mpw interface and the remote-label is another 20-bit number which will be used to create the output label header.
- Sets the destination address where this mpw should output. The dest-address is an IPv4 address that will be used to find the nexthop in the MPLS network.
The following options are available for a pflow(4) interface:
- Set the receiver address and the port for pflow(4) packets. Both must be defined to export pflow data. addr is the IP address and port is the port number of the flow collector. Pflow data will be sent to this address/port.
- Unset the receiver address and stop sending pflow data.
- Set the source IP address for pflow packets. addr is the IP address used as sender of the UDP packets and may be used to identify the source of the data on the pflow collector.
- Unset the source address.
- Set the protocol version. The default is version 5.
The following options are available for a pfsync(4) interface:
- Defer transmission of the first packet in a state until a peer has acknowledged that the associated state has been inserted. See pfsync(4) for more information.
- Do not defer the first packet in a state. This is the default.
- Indicate the maximum number of updates for a single state which can be collapsed into one. This is an 8-bit number; the default value is 128.
- Use the specified interface to send and receive pfsync state synchronisation messages.
- Stop sending pfsync state synchronisation messages over the network.
- Make the pfsync link point-to-point rather than using multicast to broadcast the state synchronisation messages. The peer_address is the IP address of the other host taking part in the pfsync cluster. With this option, pfsync(4) traffic can be protected using ipsec(4).
- Broadcast the packets using multicast.
pppoe(4) uses the sppp(4) "generic" SPPP framework. Any options not described in the section immediately following are described in the SPPP section, below.
The following options are available for a pppoe(4) interface:
- Set the name of the access-concentrator.
- Clear a previously set access-concentrator name.
- Set the name of the interface through which packets will be transmitted and received.
- Set the service name of the interface.
- Clear a previously set service name.
SPPP (PPP LINK CONTROL PROTOCOL)
The following options are available for an sppp(4) or pppoe(4) interface:
- Set the client key or password for the PPP authentication protocol.
- Set the client name for the PPP authentication protocol.
- Set the PPP authentication protocol on the specified interface acting as a
client. The protocol name can be either
pap’, or ‘
none’. In the latter case, authentication will be turned off.
- Set a specified PPP flag for the remote authenticator. The flag name can
be either ‘
callin’ or ‘
norechallenge’. The ‘
callin’ flag will require the remote peer to authenticate only when he's calling in, but not when the peer is called by the local client. This is required for some peers that do not implement the authentication protocols symmetrically. The ‘
norechallenge’ flag is only meaningful with the CHAP protocol to not re-challenge once the initial CHAP handshake has been successful. This is used to work around broken peer implementations that can't grok being re-challenged once the connection is up.
- Remove a specified PPP flag for the remote authenticator.
- Set the authenticator key or password for the PPP authentication protocol.
- Set the authenticator name for the PPP authentication protocol.
- Set the PPP authentication protocol on the specified interface acting as
an authenticator. The protocol name can be either
pap’, or ‘
none’. In the latter case, authentication will be turned off.
The following options are available for a trunk(4) interface:
- Add child-iface as a trunk port.
- Remove the trunk port child-iface.
- Set the trunk protocol. Refer to trunk(4) for a complete list of the available protocols,
The following options are available for a tunnel interface:
- Remove the source and destination tunnel addresses.
- Enable gre(4) keepalive with a packet sent every period seconds. A second timer is run with a timeout of count * period. If no keepalive response is received during that time, the link is considered down. The minimal usable count is 2 since the round-trip time of keepalive packets needs to be accounted for.
- Disable the gre(4) keepalive mechanism.
- Set the source and destination tunnel addresses on a tunnel interface, including gif(4). Packets routed to this interface will be encapsulated in IPv4 or IPv6, depending on the source and destination address families. Both addresses must be of the same family. The optional destination port can be specified for interfaces such as vxlan(4), which further encapsulate the packets in UDP datagrams.
- Use routing table tableid instead of the default table. The tunnel does not need to terminate in the same routing domain as the interface itself. tableid can be set to any valid routing table ID; the corresponding routing domain is derived from this table.
- Set the IP or multicast TTL of the tunnel packets.
- Set the virtual network identifier. This is a number which is used by tunnel protocols such as vxlan(4) to identify packets with a virtual network. The accepted size of the number depends on the individual tunnel protocol; it is a 24-bit number for vxlan(4).
The following options are available for a vlan(4) interface:
- Set the vlan tag value to vlan-tag. This value is a 12-bit number which is used to create an 802.1Q vlan header for packets sent from the vlan interface. This value cannot be changed once it is set for an interface.
- Associate with interface parent-interface. Packets
transmitted through the vlan interface will be diverted to the specified
interface parent-interface with 802.1Q vlan tagging.
Packets with 802.1Q tagging received by the parent interface with the
correct vlan tag will be diverted to the associated vlan pseudo-device.
The vlan interface is assigned a copy of the parent interface's flags and
the parent's Ethernet address. If
vlanare not set at the same time, the vlan tag will be inferred from the interface name, for instance
vlan5will be assigned 802.1Q tag 5.
- Disassociate from the parent interface. This breaks the link between the vlan interface and its parent, clears its vlan tag, flags, and link address, and shuts the interface down.
Assign the address of 192.168.1.10 with a network mask of 255.255.255.0 to interface fxp0:
# ifconfig fxp0 inet 192.168.1.10 netmask 255.255.255.0
Configure the xl0 interface to use 100baseTX, full duplex:
# ifconfig xl0 media 100baseTX mediaopt full-duplex
Label the em0 interface as an uplink:
# ifconfig em0 description "Uplink to Gigabit Switch 2"
Create the gif1 network interface:
# ifconfig gif1 create
Put the athn0 wireless interface into monitor mode:
# ifconfig athn0 mediaopt monitor
Messages indicating the specified interface does not exist, the requested address is unknown, or the user is not privileged and tried to alter an interface's configuration.
netstat(1), ifmedia(4), inet(4), intro(4), netintro(4), hostname.if(5), hosts(5), networks(5), rc(8), tcpdump(8)
ifconfig command appeared in