OpenBSD manual page server

Manual Page Search Parameters

GRE(4) Device Drivers Manual GRE(4)

greencapsulating network device

pseudo-device gre

The gre network interface allows tunnel construction using the Cisco GRE or the Mobile-IP (RFC 2004) encapsulation protocols.

GRE, WCCPv1, and MobileIP are enabled with the following sysctl(3) variables respectively in /etc/sysctl.conf:

net.inet.gre.allow
Allow GRE packets in and out of the system.
net.inet.gre.wccp
Allow WCCPv1-style GRE packets into the system (depends on the above).
net.inet.mobileip.allow
Allow MobileIP packets in and out of the system.

A gre interface can be created at runtime using the ifconfig greN create command or by setting up a hostname.if(5) configuration file for netstart(8).

This driver currently supports the following modes of operation:

GRE encapsulation (IP protocol number 47).
Encapsulated datagrams are prepended by an outer datagram and a GRE header. The GRE header specifies the type of the encapsulated datagram and thus allows for tunneling other protocols than IP like e.g. AppleTalk. GRE mode is the default tunnel mode on Cisco routers. This is also the default mode of operation of the gre interfaces.
MOBILE encapsulation (IP protocol number 55).
Datagrams are encapsulated into IP, but with a much smaller encapsulation header. This protocol only supports IP in IP encapsulation, and is intended for use with mobile IP.

The network interfaces are named gre0, gre1, etc. The number of interfaces is given by the corresponding pseudo-device line in the system configuration file. gre interfaces support the following ioctl(2)s:

struct ifreq *
Set the IP address of the local tunnel end.
struct ifreq *
Set the IP address of the remote tunnel end.
struct ifreq *
Query the IP address that is set for the local tunnel end.
struct ifreq *
Query the IP address that is set for the remote tunnel end.
struct ifreq *
Set the operation mode to the specified IP protocol value. The protocol is passed to the interface in the ifr_flags field of the ifreq structure. The operation mode can also be set with the following modifiers to ifconfig(8):

struct ifreq *
Query operation mode.

Note that the IP addresses of the tunnel endpoints may be the same as the ones defined with ifconfig(8) for the interface (as if IP is encapsulated), but need not be, as e.g. when encapsulating AppleTalk.

Configuration example:

Host X ---- Host A ------------ tunnel ------------ Cisco D ---- Host E
               \                                      /
                \                                    /
                 +------ Host B ------ Host C ------+

On Host A (OpenBSD):

# route add default B
# ifconfig greN create
# ifconfig greN A D netmask 0xffffffff linkX up
# ifconfig greN tunnel A D
# route add E D

On Host D (Cisco):

Interface TunnelX
 ip unnumbered D   ! e.g. address from Ethernet interface
 tunnel source D   ! e.g. address from Ethernet interface
 tunnel destination A
ip route C <some interface and mask>
ip route A mask C
ip route X mask tunnelX

OR

On Host D (OpenBSD):

# route add default C
# ifconfig greN create
# ifconfig greN D A
# ifconfig greN tunnel D A

To reach Host A over the tunnel (from Host D), there has to be an alias on Host A for the Ethernet interface:

# ifconfig <etherif> alias Y

and on the Cisco:

ip route Y mask tunnelX

Keepalive packets may optionally be sent to the remote endpoint, which decapsulates and returns them, allowing tunnel failure to be detected. Enable them like this:

# ifconfig greN keepalive period count

This will send a keepalive packet every period seconds. If no response is received in count * period seconds, the link is considered down. To return keepalives, the remote host must be configured to forward packets:

# sysctl net.inet.ip.forwarding=1

The MTU of gre interfaces is set to 1476 by default to match the value used by Cisco routers. This may not be an optimal value, depending on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).

For correct operation, the gre device needs a route to the destination, that is less specific than the one over the tunnel. (There needs to be a route to the decapsulating host that does not run over the tunnel, as this would create a loop.)

In order for ifconfig(8) to actually mark the interface as up, the keyword up must be given last on its command line.

The kernel must be set to forward datagrams by issuing the appropriate option to sysctl(8).

The GRE interface will accept WCCPv1-style GRE encapsulated packets from a Cisco router. Some magic with the packet filter configuration and a caching proxy like squid are needed to do anything useful with these packets.

inet(4), ip(4), netintro(4), options(4), hostname.if(5), protocols(5), ifconfig(8), netstart(8), sysctl(8)

Generic Routing Encapsulation, RFC 1701.

Generic Routing Encapsulation over IPv4 networks, RFC 1702.

Minimal Encapsulation within IP, RFC 2004.

Web Cache Coordination Protocol V1.0, http://www.wrec.org/Drafts/draft-ietf-wrec-web-pro-00.txt.

Web Cache Coordination Protocol V2.0, http://www.wrec.org/Drafts/draft-wilson-wrec-wccp-v2-00.txt.

Heiko W.Rupp ⟨hwr@pilhuhn.de⟩

GRE RFC not yet fully implemented (no GRE options).

For the WCCP GRE encapsulated packets we can only reliably accept WCCPv1 format; WCCPv2 formatted packets add another header which will skew the decode, and results are not defined (i.e. don't do WCCPv2).

July 9, 2011 OpenBSD-5.1