|open, openat(2)||open or create a file for reading or writing|
|open(3p)||perl pragma to set default PerlIO layers for input and output|
|OPEN(2)||System Calls Manual||OPEN(2)|
char *path, int
fd, const char
*path, int flags,
O_CREATflag), in which case the file is created with a mode specified by an additional argument of type mode_t as described in chmod(2) and modified by the process' umask value (see umask(2)).
The flags specified are a bitwise OR of the following values. Exactly one of the first three values (file access modes) must be specified:
Any combination of the following flags may additionally be used:
O_CREATis set and file exists.
FD_CLOEXEC(the close-on-exec flag) on the new file descriptor.
Opening a file with
O_APPEND set causes
each write on the file to be appended to the end. If
O_TRUNC and a writing mode are specified and the
file exists, the file is truncated to zero length. If
O_EXCL is set with
and the file already exists,
open() returns an
error. This may be used to implement a simple exclusive access locking
mechanism. If either of
O_NOFOLLOW are set and the last component of the
pathname is a symbolic link,
open() will fail even
if the symbolic link points to a non-existent name. If the
O_NONBLOCK flag is specified, do not wait for the
device or file to be ready or available. If the
open() call would result in the process being
blocked for some reason (e.g., waiting for carrier on a dialup line),
open() returns immediately. This flag also has the
effect of making all subsequent I/O on the open file non-blocking. If the
O_SYNC flag is set, all I/O operations on the file
will be done synchronously.
A FIFO should either be opened with
O_RDONLY or with
The behavior for opening a FIFO with
When opening a file, a lock with
flock(2) semantics can be obtained by
O_SHLOCK for a shared lock, or
O_EXLOCK for an exclusive lock. If creating a file
O_CREAT, the request for the lock will never
fail (provided that the underlying filesystem supports locking).
open() is successful, the file pointer
used to mark the current position within the file is set to the beginning of
When a new file is created it is given the group of the directory which contains it.
The system imposes a limit on the number of file descriptors open simultaneously by one process. getdtablesize(3) returns the current system limit.
openat() function is equivalent to
open() except that where path
specifies a relative path, the file to be opened is determined relative to
the directory associated with file descriptor fd
instead of the current working directory.
openat() is passed the special value
AT_FDCWD (defined in
<fcntl.h>) in the
fd parameter, the current working directory is used
and the behavior is identical to a call to
open() returns a non-negative integer, termed a file descriptor. Otherwise, a value of -1 is returned and errno is set to indicate the error.
openat() functions will fail if:
O_DIRECTORYis specified and path does not name a directory.
NAME_MAXcharacters, or an entire pathname (including the terminating NUL) exceeded
O_CREATis not set and the named file does not exist.
O_CREATis specified, the file does not exist, and the directory in which it is to be created does not permit writing.
O_NOFOLLOWflag was specified and the target is a symbolic link.
O_WRONLYflags are set, and no process has the file open for reading.
open() operation was interrupted by a signal.
O_EXLOCKis specified but the underlying filesystem does not support locking.
O_NONBLOCKand one of
O_EXLOCKis specified and the file is already locked.
O_CREATis specified, the file does not exist, and the directory in which the entry for the new file is being placed cannot be extended because there is no space left on the file system containing the directory.
O_CREATis specified, the file does not exist, and there are no free inodes on the file system on which the file is being created.
O_CREATis specified, the file does not exist, and the directory in which the entry for the new file is being placed cannot be extended because the user's quota of disk blocks on the file system containing the directory has been exhausted.
O_CREATis specified, the file does not exist, and the user's quota of inodes on the file system on which the file is being created has been exhausted.
open() call requests write access.
O_EXCLwere specified and the file exists.
O_APPENDwas not specified in flags.
openat() function will
AT_FDCWDnor a valid file descriptor.
openat() functions conform to IEEE Std 1003.1-2008 (“POSIX.1”).
POSIX specifies three different flavors
for synchronous I/O:
OpenBSD, these are all equivalent.
O_EXLOCK flags are non-standard extensions and
should not be used if portability is of concern.
open() system call first appeared in Version 1 AT&T UNIX. The flags argument has been supported since 4.2BSD. Before that, a dedicated
creat() system call had to be used to create new files; it appeared in Version 1 AT&T UNIX, was deprecated in 4.3BSD-Reno, and removed in OpenBSD 5.0.
openat() system call has been
available since OpenBSD 5.0.
O_TRUNCflag requires that one of
O_WRONLYalso be specified, else
|January 19, 2015||OpenBSD-current|