NAME
ath
—
Atheros IEEE 802.11a/b/g wireless
network device with GPIO
SYNOPSIS
ath* at pci? dev ? function ?
ath* at cardbus? dev ? function ?
gpio* at ath?
DESCRIPTION
The ath
driver provides support for
wireless network devices based on the Atheros AR5210, AR5211, and AR5212
chips.
All host/device interaction is via DMA. The
ath
driver encapsulates all IP and ARP traffic as
802.11 frames, though it can receive either 802.11 or 802.3 frames. Transmit
speed and operating mode is selectable and depends on the specific
chipset.
Support for the various devices is as follows:
- AR5210
- These devices support 802.11a operation with transmit speeds of 6 Mbps, 9 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps.
- AR5211
- These devices support 802.11a and 802.11b operation with transmit speeds as above for 802.11a and 1Mbps, 2Mbps, 5.5 Mbps, and 11Mbps for 802.11b operation.
- AR5212
- These devices support 802.11a, 802.11b, and 802.11g operation with transmit speeds as above for 802.11a, 802.11b, and 802.11g operation (802.11g speeds are the same as for 802.11a speeds).
All chips also support an Atheros Turbo Mode (TM) that operates in the 802.11a frequency range with 2x the transmit speeds. (This mode is, however, only interoperable with other Atheros-based devices.)
The actual transmit speed used is dependent on signal quality and the “rate control” algorithm employed by the driver.
These are the modes the ath
driver can
operate in:
- BSS mode
- Also known as infrastructure mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.
- IBSS mode
- Also known as IEEE ad-hoc mode or peer-to-peer mode. This is the standardized method of operating without an access point. Stations associate with a service set. However, actual connections between stations are peer-to-peer.
- Host AP
- In this mode the adapter acts as an access point (base station) for other cards.
- monitor mode
- In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.
The ath
driver can be configured to use
Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA-PSK and
WPA2-PSK). WPA is the de facto encryption standard for wireless networks. It
is strongly recommended that WEP not be used as the sole mechanism to secure
wireless communication, due to serious weaknesses in it.
AR5211 and AR5212 support the AES, TKIP, and Michael cryptographic operations required for WPA in hardware but at this time the driver does not support them.
The ath
driver can be configured at
runtime with
ifconfig(8) or on boot with
hostname.if(5).
HARDWARE
Devices supported by the ath
driver come
in either CardBus or Mini PCI packages. Wireless cards in CardBus slots may
be inserted and ejected on the fly.
The following cards are among those supported by the
ath
driver:
Card | Chip | Bus | Standard |
3Com 3CRPAG175 | AR5212 | CardBus | a/b/g |
Cisco AIR-CB21AG | AR5212 | CardBus | a/b/g |
D-Link DWL-A650 | AR5210 | CardBus | a |
D-Link DWL-AB650 | AR5211 | CardBus | a/b |
D-Link DWL-A520 | AR5210 | PCI | a |
Elecom LD-WL54 | AR5211 | CardBus | a |
IBM 11ABG WL LAN | AR5212 | Mini PCI | a/b/g |
Linksys WPC51AB | AR5211 | CardBus | a/b |
Netgear WAB501 | AR5211 | CardBus | a/b |
Planet WL-3560 | AR5211 | CardBus | a/b/g |
Proxim Skyline 4030 | AR5210 | CardBus | a |
Proxim Skyline 4032 | AR5210 | PCI | a |
Senao NL-5354MP | AR5212 | Mini PCI | a/b/g |
SMC SMC2735W | AR5210 | CardBus | a |
Sony PCWA-C500 | AR5210 | CardBus | a |
Wistron CM9 | AR5212 | Mini PCI | a/b/g |
EXAMPLES
The following hostname.if(5) example configures ath0 to join whatever network is available on boot, using WEP key “0x1deadbeef1”, channel 11, obtaining an IP address using DHCP:
dhcp NONE NONE NONE nwkey 0x1deadbeef1 chan 11
The following hostname.if(5) example creates a host-based access point on boot:
inet 192.168.1.1 255.255.255.0 NONE media autoselect \ mediaopt hostap nwid my_net chan 11
Configure ath0 to join network “my_net” using WPA with passphrase “my_passphrase”:
# ifconfig ath0 nwid my_net wpakey my_passphrase
Join an existing BSS network, “my_net”:
# ifconfig ath0 192.168.1.1 netmask 0xffffff00 nwid my_net
DIAGNOSTICS
- ath%d: unable to attach hardware; HAL status %u
- The Hardware Access Layer was unable to configure the hardware as requested. The status code is explained in the HAL include file sys/dev/ic/ar5xxx.h.
- ath%d: failed to allocate descriptors: %d
- The driver was unable to allocate contiguous memory for the transmit and receive descriptors. This usually indicates system memory is scarce and/or fragmented.
- ath%d: unable to setup a data xmit queue!
- The request to the HAL to set up the transmit queue for normal data frames failed. This should not happen.
- ath%d: unable to setup a beacon xmit queue!
- The request to the HAL to set up the transmit queue for 802.11 beacon frames failed. This should not happen.
- ath%d: hardware error; resetting
- An unrecoverable error in the hardware occurred. Errors of this sort include unrecoverable DMA errors. The driver will reset the hardware and continue.
- ath%d: rx FIFO overrun; resetting
- The receive FIFO in the hardware overflowed before the data could be transferred to the host. This typically occurs because the hardware ran short of receive descriptors and had no place to transfer received data. The driver will reset the hardware and continue.
- ath%d: unable to reset hardware; hal status %u
- The Hardware Access Layer was unable to reset the hardware as requested. The status code is explained in the HAL include file /sys/dev/ic/ar5xxx.h. This should not happen.
- ath%d: unable to initialize the key cache
- The driver was unable to initialize the hardware key cache. This should not happen.
- ath%d: unable to start recv logic
- The driver was unable to restart frame reception. This should not happen.
- ath%d: device timeout
- A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware and continue. This should not happen.
- ath%d: bogus xmit rate 0x%x
- An invalid transmit rate was specified for an outgoing frame. The frame is discarded. This should not happen.
- ath%d: ath_chan_set: unable to reset channel %u (%u MHz)
- The Hardware Access Layer was unable to reset the hardware when switching channels during scanning. This should not happen.
- ath%d: unable to allocate channel table
- The driver was unable to allocate memory for the table used to hold the set of available channels.
- ath%d: unable to collect channel list from hal
- A problem occurred while querying the HAL to find the set of available channels for the device. This should not happen.
- ath%d: failed to enable memory mapping
- The driver was unable to enable memory-mapped I/O to the PCI device registers. This should not happen.
- ath%d: failed to enable bus mastering
- The driver was unable to enable the device as a PCI bus master for doing DMA. This should not happen.
- ath%d: cannot map register space
- The driver was unable to map the device registers into the host address space. This should not happen.
- ath%d: could not map interrupt
- The driver was unable to allocate an IRQ for the device interrupt. This should not happen.
- ath%d: could not establish interrupt
- The driver was unable to install the device interrupt handler. This should not happen.
SEE ALSO
arp(4), cardbus(4), gpio(4), ifmedia(4), intro(4), netintro(4), pci(4), hostname.if(5), gpioctl(8), hostapd(8), ifconfig(8)
HISTORY
The ath
device driver first appeared in
FreeBSD 5.2 using a binary-only HAL module which was
ported to NetBSD 2.0. The driver using a free
HAL-replacement first appeared in OpenBSD 3.7.
AUTHORS
The ath
driver was written by
Sam Leffler, and was ported to
OpenBSD by Reyk Floeter
⟨reyk@openbsd.org⟩ who also wrote a free replacement of the
binary-only HAL.
CAVEATS
Different regulatory domains may not be able to communicate with each other with 802.11a as different regulatory domains do not necessarily have overlapping channels.
Host AP mode doesn't support power saving. Clients attempting to use power saving mode may experience significant packet loss (disabling power saving on the client will fix this).
BUGS
Performance in lossy environments is suboptimal. The algorithm used to select the rate for transmitted packets is very simplistic. There is no software retransmit; only hardware retransmit is used. Contributors are encouraged to replace the existing rate control algorithm with a better one.
The driver does not fully enable power-save operation of the chip; consequently power use is suboptimal.