NAME
sensorsd.conf —
configuration file for
sensorsd
DESCRIPTION
The sensorsd.conf file is read by
sensorsd(8) to configure hardware sensor monitoring. Each variable in
the sysctl(2) hw.sensors subtree represents a
sensor. Each sensor is matched by at most one entry in
sensorsd.conf, which may specify high and low
limits, and whether sensor status changes provided by the driver should be
ignored. Each time the limits are crossed in either direction or the status
provided by the driver changes,
sensorsd(8)'s alert functionality is triggered and a command, if
specified, is executed.
sensorsd.conf follows the syntax of
configuration databases as documented in
cgetent(3). Sensors may be specified by their full
hw.sensors
sysctl(8) variable name or by type, with the full name taking
precedence. For example, if an entry “hw.sensors.lm0.temp1” is
not found, then an entry for “temp” will instead be looked
for.
The following attributes may be used:
The values for temperature sensors can be given in degrees Celsius or Fahrenheit, for voltage sensors in volts, and fan speed sensors take a unit-less number representing RPM. For Boolean sensors, specify 0 for "Off" or 1 for "On". Values for all other types of sensors can be specified in the same units as they appear under the sysctl(8) hw.sensors tree.
Sensors that provide status (such as those from bio(4), esm(4), or ipmi(4)) do not require boundary values specified and simply trigger on status transitions. If boundaries are specified nonetheless, then they are used in addition to automatic status monitoring, unless the “istatus” attribute is specified to ignore status values that are provided by the drivers.
The command is executed when there is any change in sensor state. Tokens in the command are substituted as follows:
- %l
- Whether the value exceeds or is within the user specified limits. Can be one of: "below", "above", "within", "invalid", or "uninitialised".
- %n
- The sensor number.
- %s
- The sensor status.
- %x
- The xname of the device the sensor sits on.
- %t
- The type of sensor.
- %2
- The sensor's current value.
- %3
- The sensor's low limit.
- %4
- The sensor's high limit.
For Boolean sensors, %2, %3, and %4 are substituted with "On" or "Off".
By default, sensorsd(8) monitors status changes on all sensors that keep their state. This behaviour may be altered by using the “istatus” attribute to ignore status changes of sensors of a certain type or individual sensors.
FILES
- /etc/sensorsd.conf
- Configuration file for sensorsd(8).
- /etc/examples/sensorsd.conf
- Example configuration file.
EXAMPLES
In the following configuration file, if hw.sensors.ipmi0.temp0 moves upwards beyond 80C or downwards to 80C or less or if its status as provided by ipmi(4) changes, the command /etc/sensorsd/log_warning will be executed, with the sensor type, number and current value passed to it. Alerts will be sent if hw.sensors.lm0.volt3 moves into or out of the range from 4.8V to 5.2V, inclusive; if the speed of the fan attached to hw.sensors.lm0.fan1 transitions to being below or above 1000RPM; if any RAID volume drive changes its status from, for example, “OK”, such as in the case of drive failure, rebuild, or a complete failure, the command /etc/sensorsd/drive will be executed, with the sensor number passed to it; however, no alerts will be generated for status changes on timedelta sensors. For all other sensors whose drivers automatically provide sensor status updates, alerts will be generated each time those sensors undergo status transitions.
# Comments are allowed hw.sensors.ipmi0.temp0:high=80C:command=/etc/sensorsd/log_warning %t %n %2 hw.sensors.lm0.volt3:low=4.8V:high=5.2V hw.sensors.lm0.fan1:low=1000 drive:command=/etc/sensorsd/drive %n timedelta:istatus #ignore status changes for timedelta
SEE ALSO
HISTORY
The sensorsd.conf file format first
appeared in OpenBSD 3.5. The format was altered in
OpenBSD 4.1 to accommodate hierarchical device-based
sensor addressing. The “istatus” attribute was introduced in
OpenBSD 4.2.
CAVEATS
Alert functionality is triggered every time there is a change in sensor state; for example, when sensorsd(8) is started, the status of each monitored sensor changes from undefined to whatever it is. One must keep this in mind when using commands that may unconditionally perform adverse actions (e.g. shutdown(8)), as they will be executed even when all sensors perform to specification. If this is undesirable, then a wrapper shell script should be used instead.