OpenBSD manual page server

Manual Page Search Parameters

RTWN(4) Device Drivers Manual RTWN(4)

rtwnRealtek RTL8188CE/RTL8188EE/RTL8192CE/RTL8723AE PCIe IEEE 802.11b/g/n wireless network device

rtwn* at pci? port ?

The rtwn driver supports PCIe wireless network devices based on the Realtek RTL8188CE, RTL8188EE, RTL8192CE and RTL8723AE chipsets.

The RTL8188CE, RTL8188EE and RTL8723AE are highly integrated 802.11n adapters that combine a MAC, a 1T1R capable baseband and an RF in a single chip. The RTL8723AE also includes a Bluetooth 2.1/3.0/4.0 controller.

The RTL8192CE is a highly integrated multiple-in, multiple-out (MIMO) 802.11n adapter that combines a MAC, a 2T2R capable baseband and an RF in a single chip.

These devices operate in the 2GHz spectrum only.

These are the modes the rtwn driver can operate in:

BSS mode
Also known as mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.
monitor mode
In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.

The rtwn driver can be configured to use Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA1 and WPA2). WPA2 is the current encryption standard for wireless networks. It is strongly recommended that neither WEP nor WPA1 are used as the sole mechanism to secure wireless communication, due to serious weaknesses. WPA1 is disabled by default and may be enabled using the option "wpaprotos wpa1,wpa2". For standard WPA networks which use pre-shared keys (PSK), keys are configured using the "wpakey" option. WPA-Enterprise networks require use of the wpa_supplicant package.

The rtwn driver can be configured at runtime with ifconfig(8) or on boot with hostname.if(5).

The adapter needs firmware files to run, which are loaded on demand by the driver when the device is attached:

/etc/firmware/rtwn-rtl8188e
 
/etc/firmware/rtwn-rtl8192cU
 
/etc/firmware/rtwn-rtl8192cU_B
 
/etc/firmware/rtwn-rtl8723
 
/etc/firmware/rtwn-rtl8723_B
 

The following example scans for available networks:

# ifconfig rtwn0 scan

The following hostname.if(5) example configures rtwn0 to join network “mynwid”, using WPA key “mywpakey”, obtaining an IP address using DHCP:

join mynwid wpakey mywpakey
inet autoconf

rtwn0: could not read firmware ...
For some reason, the driver was unable to read the microcode file from the filesystem. The file might be missing or corrupted.
rtwn0: device timeout
A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware. This should not happen.

arp(4), ifmedia(4), intro(4), netintro(4), pci(4), hostname.if(5), ifconfig(8)

The rtwn driver first appeared in OpenBSD 5.8.

The rtwn driver was written by Stefan Sperling <stsp@openbsd.org>. It was based on the urtwn(4) driver written by Damien Bergamini <damien.bergamini@free.fr>.

The rtwn driver does not support any of the 802.11n capabilities offered by the adapters. Additional work is required in ieee80211(9) before those features can be supported.

This driver does not support powersave mode.

October 24, 2021 OpenBSD-7.5