OpenBSD manual page server

Manual Page Search Parameters

TCPBENCH(1) General Commands Manual TCPBENCH(1)

tcpbenchTCP/UDP benchmarking and measurement tool

tcpbench -l

tcpbench [-46RUuv] [-B buf] [-b addr] [-k kvars] [-n connections] [-p port] [-r interval] [-S space] [-T toskeyword] [-t secs] [-V rtable] hostname

tcpbench -s [-46Uuv] [-B buf] [-k kvars] [-p port] [-r interval] [-S space] [-T toskeyword] [-V rtable] [hostname]

tcpbench is a small tool that performs throughput benchmarking and concurrent sampling of kernel network variables.

tcpbench is run as a client/server pair. The server must be invoked with the -s flag, which will cause it to listen for incoming connections. The client must be invoked with the hostname of a listening server to connect to.

Once connected, the client will send TCP or UDP traffic as fast as possible to the server. Both the client and server will periodically display throughput statistics along with any kernel variables the user has selected to sample (using the -k option, which is only available in TCP mode). A list of available kernel variables may be obtained using the -l option.

The options are as follows:

Forces tcpbench to use IPv4 addresses only.
Forces tcpbench to use IPv6 addresses only.
buf
Specify the size of the internal read/write buffer used by tcpbench. The default is 262144 bytes for TCP client/server and UDP server. In UDP client mode this may be used to specify the packet size on the test stream.
addr
Specifies the IP address of the interface which is used to send the packets.
kvars
Specify one or more kernel variables to monitor; multiple variables must be separated with commas. This option is only valid in TCP mode. The default is not to monitor any variables. Using this option requires read access to /dev/kmem, which may be restricted based upon the value of the kern.allowkmem sysctl(8).
List the name of kernel variables available for monitoring and exit.
connections
Use the given number of TCP connections (default: 1). UDP is connectionless so this option isn't valid.
port
Specify the port used for the test stream (default: 12345).
In client mode the write buffer size is randomized up to the size specified via -B.
interval
Specify the statistics interval reporting rate in milliseconds (default: 1000).
space
Set the size of the socket buffer used for the test stream. On the client this option will resize the send buffer; on the server it will resize the receive buffer.
Place tcpbench in server mode, where it will listen on all interfaces for incoming connections. It defaults to using TCP if -u is not specified.
toskeyword
Change the IPv4 TOS or IPv6 TCLASS value. toskeyword may be one of critical, inetcontrol, lowdelay, netcontrol, throughput, reliability, or one of the DiffServ Code Points: ef, af11 ... af43, cs0 ... cs7; or a number in either hex or decimal.
secs
Stop after secs seconds.
Use AF_UNIX sockets instead of IPv4 or IPv6 sockets. In client and server mode hostname is used as the path to the AF_UNIX socket.
Use UDP instead of TCP; this must be specified on both the client and the server. Transmitted packets per second (TX PPS) will be accounted on the client side, while received packets per second (RX PPS) will be accounted on the server side. UDP has no Protocol Control Block (PCB) so the -k flags don't apply.
rtable
Set the routing table to be used.
Display verbose output. If specified more than once, increase the detail of information displayed.

netstat(1), pstat(8)

The tcpbench program first appeared in OpenBSD 4.4.

The tcpbench program was written by Damien Miller <djm@openbsd.org>.

UDP mode and libevent port by Christiano F. Haesbaert <haesbaert@haesbaert.org>.

September 25, 2016 OpenBSD-6.1