OpenBSD manual page server

NAME

inetd — internet “super-server”

SYNOPSIS

DESCRIPTION

inetd should be run at boot time by /etc/rc (see rc(8)). It then listens for connections on certain internet sockets. When a connection is found on one of its sockets, it decides what service the socket corresponds to, and invokes a program to service the request. After the program is finished, it continues to listen on the socket (except in some cases which will be described below). Essentially, inetd allows running one daemon to invoke several others, reducing load on the system.

The options are as follows:

-d

Turns on debugging.

-R rate

Specify the maximum number of times a service can be invoked in one minute; the default is 256. If a service exceeds this limit, inetd will log the problem and stop servicing requests for the specific service for ten minutes. See also the wait/nowait configuration fields below.

Upon execution, inetd reads its configuration information from a configuration file which, by default, is /etc/inetd.conf. There must be an entry for each field of the configuration file, with entries for each field separated by a tab or a space. Comments are denoted by a “#” at the beginning of a line. The fields of the configuration file are as follows:

service name
socket type
protocol
wait/nowait[.max]
user[.group] or user[:group]
server program
server program arguments

To specify a Sun-RPC based service, the entry would contain these fields.

service name/version
socket type
rpc/protocol
wait/nowait[.max]
user[.group] or user[:group]
server program
server program arguments

For internet services, the first field of the line may also have a host address specifier prefixed to it, separated from the service name by a colon. If this is done, the string before the colon in the first field indicates what local address inetd should use when listening for that service. Multiple local addresses can be specified on the same line, separated by commas. Numeric IP addresses in dotted-quad notation can be used as well as symbolic hostnames. Symbolic hostnames are looked up using gethostbyname(). If a hostname has multiple address mappings, inetd creates a socket to listen on each address.

The single character “*” indicates INADDR_ANY, meaning “all local addresses”. To avoid repeating an address that occurs frequently, a line with a host address specifier and colon, but no further fields, causes the host address specifier to be remembered and used for all further lines with no explicit host specifier (until another such line or the end of the file). A line

The service name entry is the name of a valid service in the file /etc/services. For “internal” services (discussed below), the service name must be the official name of the service (that is, the first entry in /etc/services). When used to specify a Sun-RPC based service, this field is a valid RPC service name in the file /etc/rpc. The part on the right of the “/” is the RPC version number. This can simply be a single numeric argument or a range of versions. A range is bounded by the low version to the high version - “rusers/1-3”. For UNIX-domain sockets this field specifies the path name of the socket.

The socket type should be one of “stream”, “dgram”, “raw”, “rdm”, or “seqpacket”, depending on whether the socket is a stream, datagram, raw, reliably delivered message, or sequenced packet socket.

The protocol must be a valid protocol as given in /etc/protocols. Examples might be “tcp” or “udp”. RPC based services are specified with the “rpc/tcp” or “rpc/udp” service type. “tcp” and “udp” will be recognized as “TCP or UDP over default IP version”. This is currently IPv4, but in the future it will be IPv6. If you need to specify IPv4 or IPv6 explicitly, use something like “tcp4” or “udp6”. A protocol of “unix” is used to specify a socket in the UNIX-domain.

The wait/nowait entry is used to tell inetd if it should wait for the server program to return, or continue processing connections on the socket. If a datagram server connects to its peer, freeing the socket so inetd can receive further messages on the socket, it is said to be a “multi-threaded” server, and should use the “nowait” entry. For datagram servers which process all incoming datagrams on a socket and eventually time out, the server is said to be “single-threaded” and should use a “wait” entry. comsat(8) (biff(1)) and talkd(8) are both examples of the latter type of datagram server. The optional “max” suffix (separated from “wait” or “nowait” by a dot) specifies the maximum number of times a service can be invoked in one minute; the default is 256. If a service exceeds this limit, inetd will log the problem and stop servicing requests for the specific service for ten minutes. See also the -R option above.

Stream servers are usually marked as “nowait” but if a single server process is to handle multiple connections, it may be marked as “wait”. The master socket will then be passed as fd 0 to the server, which will then need to accept the incoming connection. The server should eventually time out and exit when no more connections are active. inetd will continue to listen on the master socket for connections, so the server should not close it when it exits.

The user entry should contain the user name of the user as whom the server should run. This allows for servers to be given less permission than root. An optional group name can be specified by appending a dot to the user name followed by the group name. This allows for servers to run with a different (primary) group ID than specified in the password file. If a group is specified and user is not root, the supplementary groups associated with that user will still be set.

The server program entry should contain the pathname of the program which is to be executed by inetd when a request is found on its socket. If inetd provides this service internally, this entry should be “internal”.

The server program arguments should be just as arguments normally are, starting with argv[0], which is the name of the program. If the service is provided internally, the word “internal” should take the place of this entry.

inetd provides several “trivial” services internally by use of routines within itself. These services are “echo”, “discard”, “chargen” (character generator), “daytime” (human readable time), and “time” (machine readable time, in the form of the number of seconds since midnight, January 1, 1900). All of these services are TCP based. For details of these services, consult the appropriate RFC from the Network Information Center.

inetd rereads its configuration file when it receives a hangup signal, SIGHUP. Services may be added, deleted or modified when the configuration file is reread. inetd creates a file /var/run/inetd.pid that contains its process identifier.

SEE ALSO

comsat(8), fingerd(8), ftp-proxy(8), ftpd(8), identd(8), talkd(8)

HISTORY

The inetd command appeared in 4.3BSD. Support for Sun-RPC based services is modelled after that provided by SunOS 4.1. IPv6 support was added by the KAME project in 1999.

BUGS

Host address specifiers, while they make conceptual sense for RPC services, do not work entirely correctly. This is largely because the portmapper interface does not provide a way to register different ports for the same service on different local addresses. Provided you never have more than one entry for a given RPC service, everything should work correctly. (Note that default host address specifiers do apply to RPC lines with no explicit specifier.)