OpenBSD manual page server

NAME

an — Aironet Communications 4500/4800 IEEE 802.11FH/b wireless network device

SYNOPSIS

an* at pcmcia?
an* at pci?
an* at isapnp?

DESCRIPTION

The an driver provides support for the Aironet Communications 4500, 4800 (aka Cisco 340), and Cisco 350 IEEE 802.11 wireless network adapters. This includes the ISA, PCI, and PCMCIA varieties. The 4500 series adapters operate at 1 and 2Mbps (FH) while the 4800 and 350 series can operate at 1, 2, 5.5, and 11Mbps (DS). The ISA, PCI, and PCMCIA devices are all based on the same core PCMCIA modules and all have the same programming interface. However, unlike the Lucent WaveLAN/IEEE cards, the ISA and PCI cards appear to the host as normal ISA and PCI devices and do not require any PCMCIA support.

ISA cards can either be configured to use ISA Plug and Play or to use a particular I/O address and IRQ by properly setting the DIP switches on the board. (The default switch setting is for plug and play.) The an driver has Plug and Play support and will work in either configuration, however when using a hard-wired I/O address and IRQ, the driver configuration and the NIC's switch settings must agree. PCI cards require no switch settings of any kind and will be automatically probed and attached.

All host/device interaction with the Aironet cards is via programmed I/O. The an driver encapsulates all IP and ARP traffic as 802.11 frames, though it can receive either 802.11 or 802.3 frames.

These are the modes the an driver can operate in:

BSS mode

Also known as infrastructure mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.

IBSS mode

Also known as IEEE ad-hoc mode or peer-to-peer mode. This is the standardized method of operating without an access point. Stations associate with a service set. However, actual connections between stations are peer-to-peer.

monitor mode

In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.

The an driver can be configured to use hardware Wired Equivalent Privacy (WEP). It is strongly recommended that WEP not be used as the sole mechanism to secure wireless communication, due to serious weaknesses in it.

The an driver can be configured at runtime with ifconfig(8) or on boot with hostname.if(5).

EXAMPLES

The following example scans for available networks:

The following hostname.if(5) example configures wi0 to join network “mynwid”, using WEP key “mywepkey”, obtaining an IP address using DHCP:

nwid mynwid
nwkey mywepkey
dhcp

DIAGNOSTICS

an0: failed to allocate N bytes on NIC

The driver was unable to allocate memory for transmit frames in the NIC's on-board RAM.

an0: device timeout

The Aironet card failed to generate an interrupt to acknowledge a transmit command.

SEE ALSO

arp(4), ifmedia(4), intro(4), isapnp(4), netintro(4), pci(4), pcmcia(4), hostname.if(5), ifconfig(8)

HISTORY

The an device driver first appeared in FreeBSD 4.0. OpenBSD support was added in OpenBSD 2.7. A version of the driver based on the one in NetBSD was added in OpenBSD 3.9.

AUTHORS

The an driver was written by Bill Paul <wpaul@ee.columbia.edu> and ported to OpenBSD by Michael Shalayeff <mickey@openbsd.org>. Later the NetBSD version of the driver by Atsushi Onoe was subsequently ported to OpenBSD by Jonathan Gray <jsg@openbsd.org>.

CAVEATS

Scanning for access points is not currently supported.