OpenBSD manual page server

Manual Page Search Parameters

APMD(8) System Manager's Manual APMD(8)

apmdAdvanced Power Management daemon

apmd [-AaCdHLs] [-f devname] [-S sockname] [-t seconds]

apmd monitors the advanced power management device, apm(4), acting on signaled events and upon user requests as sent by the apm(8) program.

For suspend and standby request events delivered by the BIOS, or via apm(8), apmd runs the appropriate configuration program (if one exists), syncs the buffer cache to disk and initiates the requested state. When resuming after suspend or standby, apmd runs the appropriate configuration program (if one exists).

When the power status changes (battery is connected or disconnected) apmd fetches the current status and reports it via syslog(3) with logging facility LOG_DAEMON.

The options are as follows:

Start apmd in automatic performance adjustment mode. In this mode, when CPU idle time falls below 10%, or if the AC power is connected and the battery is more than 15% charged, or if the battery is absent, apmd raises hw.setperf to 100. Otherwise when CPU idle time is above 30% and the system is running on battery power, apmd lowers hw.setperf as much as possible to reduce power consumption.
BIOS-initiated suspend or standby requests are ignored if the system is connected to line current and not running from batteries (user requests are still honored).
Start apmd in cool running performance adjustment mode. In this mode, when CPU idle time falls below 10%, apmd raises hw.setperf as much as necessary. Otherwise when CPU idle time is above 30%, apmd lowers hw.setperf as much as possible to reduce heat, noise, and power consumption.
apmd enters debug mode, logging to facility LOG_LOCAL1, and stays in the foreground on the controlling terminal.
devname
Specify an alternate device file name, devname.
Start apmd in manual performance adjustment mode, initialising hw.setperf to 100.
Start apmd in manual performance adjustment mode, initialising hw.setperf to 0.
sockname
Specify an alternate socket name, sockname. The socket is protected to mode 0660, UID 0, GID 0; this protects access to suspend requests to authorized users only.
Current battery statistics are reported via syslog(3) and apmd exits without monitoring the APM status.
seconds
apmd periodically polls the APM driver for the current power state. If the battery charge level changes substantially or the external power status changes, the new status is logged. The polling rate defaults to once per 10 minutes, but may be specified using the -t command-line flag.

When a client requests a suspend or stand-by state, apmd does not wait for positive confirmation that the requested state has been entered before replying to the client; to do so would mean the client does not get a reply until the system resumes from its sleep state. Rather, apmd replies with the intended state to the client and then places the system in the requested state after running the configuration script and flushing the buffer cache.

Actions can be configured for the following five transitions: suspend, standby, resume, powerup, and powerdown. The suspend and standby actions are run prior to apmd performing any other actions (such as disk syncs) and entering the new state. The resume program is run after resuming from a stand-by or suspended state. The powerup and powerdown programs are run after the power status (AC connected or not) changes, as well as after a resume (if the power status changed in the mean time).

/dev/apmctl
Default device used to control the APM kernel driver.

/etc/apm/suspend
 
/etc/apm/standby
 
/etc/apm/resume
 
/etc/apm/powerup
 
/etc/apm/powerdown
These files contain the host's customized actions. Each file must be an executable binary or shell script. A single program or script can be used to control all transitions by examining the name by which it was called, which is one of suspend, standby, resume, powerup, or powerdown.

/var/run/apmdev
Default UNIX-domain socket used for communication with apm(8).

syslog(3), apm(4), apm(8), sysctl(8)

Advanced Power Management (APM) BIOS Interface Specification (revision 1.2), Intel Corporation and Microsoft Corporation.

The apmd command first appeared in NetBSD 1.3. OpenBSD support was added in OpenBSD 1.2.

October 28, 2010 OpenBSD-5.3