|HEXDUMP(1)||General Commands Manual||HEXDUMP(1)|
hexdumputility is a filter which displays the specified files, or the standard input, if no files are specified, in a user-specified format.
The options are as follows:
#’) are ignored.
0X, length is interpreted as a hexadecimal number, otherwise, with a leading
0, length is interpreted as an octal number.
0X, offset is interpreted as a hexadecimal number, otherwise, with a leading
0, offset is interpreted as an octal number. Appending the character
mto offset causes it to be interpreted as a multiple of
-voption causes hexdump to display all input data. Without the
-voption, any number of groups of output lines, which would be identical to the immediately preceding group of output lines (except for the input offsets), are replaced with a line comprised of a single asterisk (‘
For each input file,
copies the input to standard output, transforming the data according to the
format strings specified by the
-f options, in the order that they were
The iteration count is an optional positive integer, which defaults to one. Each format is applied iteration count times.
The byte count is an optional positive integer. If specified it defines the number of bytes to be interpreted by each iteration of the format.
If an iteration count and/or a byte count is specified, a single slash (‘/’) must be placed after the iteration count and/or before the byte count to disambiguate them. Any whitespace before or after the slash is ignored.
The format is required and must be surrounded by double quote (" ") marks (the quote mark is a special character in many shell programs, and may have to be escaped from the shell). It is interpreted as a fprintf-style format string (see fprintf(3)), with the following exceptions:
hexdump also supports the following
additional conversion strings:
xspecify the display base as decimal, octal or hexadecimal respectively.
_aconversion string except that it is only performed once, when all of the input data has been processed.
000 nul 001 soh 002 stx 003 etx 004 eot 005 enq 006 ack 007 bel 008 bs 009 ht 00A lf 00B vt 00C ff 00D cr 00E so 00F si 010 dle 011 dc1 012 dc2 013 dc3 014 dc4 015 nak 016 syn 017 etb 018 can 019 em 01A sub 01B esc 01C fs 01D gs 01E rs 01F us 07F del
The default and supported byte counts for the conversion characters are as follows:
The amount of data interpreted by each format string is the sum of the data required by each format unit, which is the iteration count times the byte count, or the iteration count times the number of bytes required by the format if the byte count is not specified.
The input is manipulated in “blocks”, where a block is defined as the largest amount of data specified by any format string. Format strings interpreting less than an input block's worth of data, whose last format unit both interprets some number of bytes and does not have a specified iteration count, have the iteration count incremented until the entire input block has been processed or there is not enough data remaining in the block to satisfy the format string.
If, either as a result of user specification or hexdump modifying the iteration count as described above, an iteration count is greater than one, no trailing whitespace characters are output during the last iteration.
It is an error to specify a byte count as well as multiple
conversion characters or strings unless all but one of the conversion
characters or strings is
If, as a result of the specification of the
-n option or end-of-file being reached, input data
only partially satisfies a format string, the input block is zero-padded
sufficiently to display all available data (i.e., any format units
overlapping the end of data will display some number of the zero bytes).
Further output by such format strings is replaced by an equivalent
number of spaces. An equivalent number of spaces is defined as the number of
spaces output by an
s conversion character with the
same field width and precision as the original conversion character or
conversion string but with any ‘
#’ conversion flag characters
removed, and referencing a NULL string.
If no format strings are specified, the default display is
equivalent to specifying the
hexdumputility exits 0 on success, and >0 if an error occurs.
$ hexdump -e '"%4_u"' file
An example file for use with the
option, to display the input in perusal format:
"%06.6_ao " 12/1 "%3_u " "\t\t" "%_p " "\n"
An example file for use with the
option, which implements the equivalent of the
"%07.7_Ax\n" "%07.7_ax " 8/2 " %04x " "\n"
|May 6, 2011||OpenBSD-5.1|