OpenBSD manual page server

Manual Page Search Parameters
RSU(4) Device Drivers Manual RSU(4)

rsuRealtek RTL8188SU/RTL8192SU USB IEEE 802.11b/g/n wireless network device

rsu* at uhub? port ?

The rsu driver supports USB 2.0 wireless network devices based on Realtek RTL8188SU, RTL8191SU and RTL8192SU chipsets.

The RTL8188SU is a highly integrated 802.11n adapter that combines a MAC, a 1T1R capable baseband and an RF in a single chip. It operates in the 2GHz spectrum only.

The RTL8191SU is a highly integrated multiple-in, single-out (MISO) 802.11n adapter that combines a MAC, a 1T2R capable baseband and an RF in a single chip. It operates in the 2GHz spectrum only.

The RTL8192SU is a highly integrated multiple-in, multiple-out (MIMO) 802.11n adapter that combines a MAC, a 2T2R capable baseband and an RF in a single chip. It operates in the 2GHz spectrum only.

These are the modes the rsu driver can operate in:

BSS mode
Also known as mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.

The rsu driver can be configured to use Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA1 and WPA2). WPA2 is the current encryption standard for wireless networks. It is strongly recommended that neither WEP nor WPA1 are used as the sole mechanism to secure wireless communication, due to serious weaknesses. WPA1 is disabled by default and may be enabled using the option "wpaprotos wpa1,wpa2". For standard WPA networks which use pre-shared keys (PSK), keys are configured using the "wpakey" option. WPA-Enterprise networks require use of the wpa_supplicant package.

The rsu driver can be configured at runtime with ifconfig(8) or on boot with hostname.if(5).

The adapter needs firmware files to run, which are loaded on demand by the driver when the device is attached:

/etc/firmware/rsu-rtl8712
 

The following adapters should work:

ASUS USB-N10
 
ASUS WL-167G V3
 
Belkin F7D1101 v1
 
D-Link DWA-131 A1
 
Hercules HWGUn-54
 
Hercules HWNUm-300
 
Planex GW-USNano
 
Sitecom WL-349 v1
 
Sitecom WL-353
 
Sweex LW154
 
TRENDnet TEW-648UB
 
TRENDnet TEW-649UB
 

The following example scans for available networks:

# ifconfig rsu0 scan

The following hostname.if(5) example configures rsu0 to join network “mynwid”, using WPA key “mywpakey”, obtaining an IP address using DHCP:

join mynwid wpakey mywpakey
inet autoconf

rsu0: error N, could not read firmware ...
For some reason, the driver was unable to read the microcode file from the filesystem. The file might be missing or corrupted.
rsu0: device timeout
A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware. This should not happen.

arp(4), ifmedia(4), intro(4), netintro(4), usb(4), hostname.if(5), ifconfig(8)

The rsu driver first appeared in OpenBSD 4.9.

The rsu driver was written by Damien Bergamini <damien.bergamini@free.fr>.

The rsu driver does not support any of the 802.11n capabilities offered by the adapters. Additional work is required in ieee80211(9) before those features can be supported.

This driver does not support powersave mode.

October 24, 2021 OpenBSD-current