OpenBSD manual page server

Manual Page Search Parameters
IWM(4) Device Drivers Manual IWM(4)

iwmIntel 7000/8000/9000 IEEE 802.11a/ac/b/g/n wireless network device

iwm* at pci?

The iwm driver provides support for Intel Wireless 7260, 7265, 3160, 3165, 3168, 8260, 8265, and 9260 PCIe Mini Card and M.2 network adapters, and for Intel Wireless 9560 Integrated Connectivity (CNVi) network adapters with companion RF M.2 modules.

These are the modes the iwm driver can operate in:

BSS mode
Also known as mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.
monitor mode
In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.

The iwm driver can be configured to use Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA1 and WPA2). WPA2 is the current encryption standard for wireless networks. It is strongly recommended that neither WEP nor WPA1 are used as the sole mechanism to secure wireless communication, due to serious weaknesses. WPA1 is disabled by default and may be enabled using the option "wpaprotos wpa1,wpa2". For standard WPA networks which use pre-shared keys (PSK), keys are configured using the "wpakey" option. WPA-Enterprise networks require use of the wpa_supplicant package. The iwm driver offloads both encryption and decryption of unicast data frames to the hardware for the CCMP cipher.

In BSS mode the driver supports background scanning; see ifconfig(8).

The iwm driver can be configured at runtime with ifconfig(8) or on boot with hostname.if(5).

The driver needs one of the following firmware files, which are loaded when an interface is brought up:

/etc/firmware/iwm-3160-17
 
/etc/firmware/iwm-3168-29
 
/etc/firmware/iwm-7260-17
 
/etc/firmware/iwm-7265-17
 
/etc/firmware/iwm-7265D-29
 
/etc/firmware/iwm-8000C-36
 
/etc/firmware/iwm-8265-36
 
/etc/firmware/iwm-9000-46
 
/etc/firmware/iwm-9260-46
 

These firmware files are not free because Intel refuses to grant distribution rights without contractual obligations. As a result, even though OpenBSD includes the driver, the firmware files cannot be included and users have to download these files on their own.

A prepackaged version of the firmware can be installed using fw_update(8).

The following example scans for available networks:

# ifconfig iwm0 scan

The following hostname.if(5) example configures iwm0 to join network “mynwid”, using WPA key “mywpakey”, obtaining an IP address using DHCP:

join mynwid wpakey mywpakey
inet autoconf

iwm0: device timeout
A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware. This should not happen.
iwm0: fatal firmware error
For some reason, the firmware crashed. The driver will reset the hardware. This should not happen.
iwm0: radio is disabled by hardware switch
The radio transmitter is off and thus no packet can go out. The driver will reset the hardware. Make sure the laptop radio switch is on.
iwm0: could not read firmware ... (error N)
For some reason, the driver was unable to read the firmware image from the filesystem. The file might be missing or corrupted.
iwm0: firmware too short: N bytes
The firmware image is corrupted and can't be loaded into the adapter.
iwm0: could not load firmware
An attempt to load the firmware into the adapter failed. The driver will reset the hardware.

arp(4), ifmedia(4), intro(4), netintro(4), pci(4), hostname.if(5), ifconfig(8)

The iwm device driver first appeared in OpenBSD 5.7.

This driver does not support powersave mode.

October 14, 2023 OpenBSD-current