|RAL(4)||Device Drivers Manual||RAL(4)|
ral — Ralink
Technology/MediaTek IEEE 802.11a/b/g/n wireless network device
ral* at cardbus?
ral* at pci?
ral driver supports PCI/PCIe/CardBus
wireless adapters based on the Ralink RT2500, RT2501, RT2600, RT2700,
RT2800, RT3090 and RT3900E chipsets.
The RT2500 chipset is the first generation of 802.11b/g adapters from Ralink. It consists of two integrated chips, an RT2560 MAC/BBP and an RT2525 radio transceiver.
The RT2501 chipset is the second generation of 802.11a/b/g adapters from Ralink. It consists of two integrated chips, an RT2561 MAC/BBP and an RT2527 radio transceiver. This chipset provides support for the IEEE 802.11e standard with multiple hardware transmission queues and allows scatter/gather for efficient DMA operations.
The RT2600 chipset consists of two integrated chips, an RT2661 MAC/BBP and an RT2529 radio transceiver. This chipset uses the MIMO (multiple-input multiple-output) technology with multiple radio transceivers to extend the operating range of the adapter and to achieve higher throughput. However, the RT2600 chipset does not support any of the 802.11n features.
The RT2700 chipset is a low-cost version of the RT2800 chipset. It supports a single transmit path and two receiver paths (1T2R). It consists of two integrated chips, an RT2760 or RT2790 (PCIe) MAC/BBP and an RT2720 (2.4GHz) or RT2750 (2.4GHz/5GHz) radio transceiver.
The RT2800 chipset is the first generation of 802.11n adapters from Ralink. It consists of two integrated chips, an RT2860 or RT2890 (PCIe) MAC/BBP and an RT2820 (2.4GHz) or RT2850 (2.4GHz/5GHz) radio transceiver. The RT2800 chipset supports two transmit paths and up to three receiver paths (2T2R/2T3R). It can achieve speeds up to 144Mbps (20MHz bandwidth) and 300Mbps (40MHz bandwidth.)
The RT3090 chipset is the first generation of single-chip 802.11n adapters from Ralink.
The RT3900E chipset is a single-chip 802.11n adapter from Ralink. The MAC/Baseband Processor can be an RT3290, RT5390 or RT5392. The RT3290 is a combo 802.11n and Bluetooth chip. It operates in the 2 Ghz spectrum and supports one transmit path and on one receiver path (1T1R). The RT5390 chip operates in the 2GHz spectrum and supports one transmit path and one receiver path (1T1R). The RT5392 chip operates in the 2GHz spectrum and supports up to two transmit paths and two receiver paths (2T2R).
These are the modes the
ral driver can
ral driver can be configured to use
Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA-PSK and
WPA2-PSK). WPA is the current encryption standard for wireless networks. It
is strongly recommended that WEP not be used as the sole mechanism to secure
wireless communication, due to serious weaknesses in it.
ral driver relies on the software
802.11 stack for both encryption and decryption of data frames on the
RT2500, RT2501 and RT2600 chipsets. On the RT2700 and RT2800 chipsets, the
ral driver offloads both encryption and decryption
of data frames to the hardware for the WEP40, WEP104, TKIP(+MIC) and CCMP
The transmit speed is user-selectable or can be adapted automatically by the driver depending on the number of hardware transmission retries.
In Host AP mode, devices with the RT2700, RT2800, RT3090, and RT3900E chipsets are compatible with clients using powersave.
The RT2501, RT2600, RT2700 and RT2800 chipsets require the following firmware files to be loaded when an interface is brought up:
The RT2500 chipset does not require a firmware file to operate.
The following PCI adapters should work:
The following CardBus adapters should work:
The following Mini PCI adapters should work:
The following example scans for available networks:
# ifconfig ral0 scan
The following hostname.if(5) example configures ral0 to join network “mynwid”, using WPA key “mywpakey”, obtaining an IP address using DHCP:
nwid mynwid wpakey mywpakey dhcp
The following hostname.if(5) example creates a host-based access point on boot:
mediaopt hostap nwid mynwid wpakey mywpakey inet 192.168.1.1 255.255.255.0
ral driver first appeared in
OpenBSD 3.7. Support for the RT2501 and RT2600
chipsets was added in OpenBSD 3.9. Support for the
RT2800 chipset was added in OpenBSD 4.3. Support for
the RT2700 chipset was added in OpenBSD 4.4. Support
for the RT3090 chipset was added in OpenBSD 4.9.
ral driver was written by
ral driver does not make use of the
hardware cryptographic engine present on the RT2500, RT2501 and RT2600
ral driver does not support any of the
802.11n capabilities offered by the RT2700, RT2800 and RT3090 chipsets.
Additional work is required in
ieee80211(9) before those
features can be supported.
On the RT2500, RT2501 and RT2600 chipsets, host AP mode doesn't support power saving. Clients attempting to use power saving mode may experience significant packet loss.
ral adapters seem to strictly
require a system supporting PCI 2.2 or greater and will likely not work in
systems based on older revisions of the PCI specification. Check the board's
PCI version before purchasing the card.
|March 29, 2019||OpenBSD-6.5|