|COMPRESS(1)||General Commands Manual||COMPRESS(1)|
compressutility reduces the size of the named files using adaptive Lempel-Ziv coding, in compress mode. If invoked as
-g, the deflate mode of compression is chosen; see gzip(1) for more information. Each file is renamed to the same name plus the extension “.Z”. As many of the modification time, access time, file flags, file mode, user ID, and group ID as allowed by permissions are retained in the new file. If compression would not reduce the size of a file, the file is ignored (unless
uncompress utility restores compressed
files to their original form, renaming the files by removing the extension
(or by using the stored name if the
-N flag is
specified). It has the ability to restore files compressed by both
gzip(1), recognising the
following extensions: “.Z”, “-Z”,
“_Z”, “.gz”, “-gz”,
“_gz”, “.tgz”, “-tgz”,
“_tgz”, “.taz”, “-taz”, and
“_taz”. Extensions ending in “tgz” and
“taz” are not removed when decompressing, instead they are
converted to “tar”.
zcat command is equivalent in
If renaming the files would cause files to be overwritten and the standard input device is a terminal, the user is prompted (on the standard error output) for confirmation. If prompting is not possible or confirmation is not received, the files are not overwritten.
If no files are specified, the standard input is compressed or uncompressed to the standard output. If either the input or output files are not regular files, the checks for reduction in size and file overwriting are not performed, the input file is not removed, and the attributes of the input file are not retained.
By default, when compressing using the deflate scheme
-g), the original file name and time stamp are
stored in the compressed file. When uncompressing, this information is not
used. Instead, the uncompressed file inherits the time stamp of the
compressed version and the uncompressed file name is generated from the name
of the compressed file as described above. These defaults may be overridden
The options are as follows:
-9. Compression factor
-1is the fastest, but provides a poorer level of compression. Compression factor
-9provides the best level of compression, but is relatively slow. The default is
-6. This option implies
compressand if the option
-cis also given, copy the input data without change to the standard output: let
zcatbehave as cat(1).
-v option is specified, the
following additional information is printed:
-noption is specified, the time stamp stored in the compressed file is printed instead).
-g) is used.
compresswill descend into specified directories.
compress uses a modified Lempel-Ziv
algorithm (LZW). Common substrings in the file are first replaced by 9-bit
codes 257 and up. When code 512 is reached, the algorithm switches to 10-bit
codes and continues to use more bits until the limit specified by the
-b flag is reached. bits must
be between 9 and 16 (the default is 16).
After the bits limit is reached,
compress periodically checks the compression ratio.
If it is increasing,
compress continues to use the
existing code dictionary. However, if the compression ratio decreases,
compress discards the table of substrings and
rebuilds it from scratch. This allows the algorithm to adapt to the next
“block” of the file.
-b flag is omitted for
uncompress since the bits
parameter specified during compression is encoded within the output, along
with a magic number to ensure that neither decompression of random data nor
recompression of compressed data is attempted.
The amount of compression obtained depends on the size of the
input, the number of bits per code, and the
distribution of common substrings. Typically, text such as source code or
English is reduced by 50 - 60% using
Compression is generally much better than that achieved by Huffman coding
(as used in the historical command pack), or adaptive Huffman coding (as
used in the historical command compact), and takes less time to compute.
compressutility exits with one of the following values:
-fwas not specified and compression would have resulted in a size increase.
utilities exit 0 on success, and >0 if an error occurs.
Welch, Terry A., A Technique for High Performance Data Compression, IEEE Computer, 17:6, pp. 8-19, June, 1984.
zcatutilities are compliant with the X/Open System Interfaces option of the IEEE Std 1003.1-2008 (“POSIX.1”) specification.
-hlNnoqrt], and the
-fghqr] are extensions to that
IEEE Std 1003.1-2008
(“POSIX.1”) specifies a maximum bits limit
-b) of 14 to “achieve portability to all
compresscommand appeared in 4.3BSD. Deflate compression support was added in OpenBSD 2.1.
|March 17, 2014||OpenBSD-6.1|