OpenBSD manual page server

Manual Page Search Parameters
BGPD(8) System Manager's Manual BGPD(8)

bgpd — Border Gateway Protocol daemon

bgpd [-cdnv] [-D macro=value] [-f file]

bgpd is a Border Gateway Protocol (BGP) daemon which manages the network routing tables. Its main purpose is to exchange information concerning "network reachability" with other BGP systems. bgpd uses the Border Gateway Protocol, Version 4, as described in RFC 4271.

BGP is an exterior gateway protocol using a multiple step decision process to find the best path. Advanced filtering can be used to influence the route decision for traffic engineering. The session engine of bgpd is responsible for maintaining the TCP session with each neighbor. Updates are passed to the Route Decision Engine (RDE) where the paths are filtered and used to compute a Routing Information Base (RIB). The parent process is responsible for keeping the RIB in sync with the kernel routing table.

The route decision process selects the best path by evaluating all paths to the same destination. The decision process continues to the next step if paths have equal attributes. Paths that are less preferred are taken out of consideration until there is only one path left.

  1. All paths with errors or loops are not eligible.
  2. Paths with an unreachable nexthop are not eligible. After this step all remaining paths are valid.
  3. The path with the highest is selected.
  4. The path with the shortest attribute is selected.
  5. The attribute is compared. The order is IGP before EGP before incomplete origins.
  6. The path with the lowest metric is selected. Normally, this value is only considered when choosing between multiple routes sent by the same neighbouring AS. However, if “rde med compare always” is set in the configuration, the metric is compared for routes sent by any AS.
  7. Comparison of the BGP session type. Paths learned over an external (EBGP) session are preferred over those learned via an internal (IBGP) session.
  8. The path with the lowest local weight is selected.
  9. If “rde route-age evaluate” is set then the oldest path is selected.
  10. The path coming from the neighbor with the lowest wins. If the attribute is present that value will be used in the comparison instead.
  11. The path with the shortest attribute is selected. If it is not present then a length of 0 is used in the comparison.
  12. The path coming from the peer with the lowest IP address is selected. IPv4 sessions will be preferred over IPv6 ones.
  13. In case of locally announced prefixes bgpd will prefer statically set prefixes over dynamically inserted ones.

Attributes set by filters can be used to tip the decision process to prefer particular paths over others. This can be achieved by changing the , med, or weight attributes. AS path prepending or changing the med or attribute can be used to influence the routing behaviour on remote systems.

bgpd is usually started at boot time, and can be enabled by setting the following in /etc/rc.conf.local:

bgpd_flags=""

See rc(8) and rc.conf(8) for more information on the boot process and enabling daemons.

When bgpd starts up, it reads settings from a configuration file, typically bgpd.conf(5). A running bgpd process can be controlled using the bgpctl(8) utility.

The options are as follows:

Force bgpd to do carp(4) demotion at startup when the functionality is used. Normally, bgpd will only do demotion at startup when the demotion counter for the group in question is already greater than 0. bgpd will start handling demotion after all sessions with demotion configured for the given group have been successfully established. At system startup, rc(8) has the demotion counter for the group increased until after bgpd is started, so this option should be used in rc.conf(8).
macro=value
Define macro to be set to value on the command line. Overrides the definition of macro in the configuration file.
Do not daemonize. If this option is specified, bgpd will run in the foreground and log to .
file
Use file as the configuration file, instead of the default /etc/bgpd.conf.
Configtest mode. Only check the configuration file for validity.
Produce more verbose output.

/etc/bgpd.conf
default bgpd configuration file
/var/run/bgpd.sock
default bgpd control socket

bgpd.conf(5), bgpctl(8), bgplg(8), bgplgsh(8)

R. Chandra, P. Traina, and T. Li, BGP Communities Attribute, RFC 1997, August 1996.

A. Heffernan, Protection of BGP Sessions via the TCP MD5 Signature Option, RFC 2385, August 1998.

P. Marques and F. Dupont, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing, RFC 2545, March 1999.

E. Chen, Route Refresh Capability for BGP-4, RFC 2918, September 2000.

G. Huston, NOPEER Community for Border Gateway Protocol (BGP) Route Scope Control, RFC 3765, April 2004.

Y. Rekhter, T. Li, and S. Hares, A Border Gateway Protocol 4 (BGP-4), RFC 4271, January 2006.

S. Sangli, D. Tappan, and Y. Rekhter, BGP Extended Communities Attribute, RFC 4360, February 2006.

E. Rosen and Y. Rekhter, BGP/MPLS IP Virtual Private Networks (VPNs), RFC 4364, February 2006.

T. Bates, E. Chen, and R. Chandra, BGP Route Reflection: An Alternative to Full Mesh Internal BGP (IBGP), RFC 4456, April 2006.

E. Chen and V. Gillet, Subcodes for BGP Cease Notification Message, RFC 4486, April 2006.

T. Bates, R. Chandra, D. Katz, and Y. Rekhter, Multiprotocol Extensions for BGP-4, RFC 4760, January 2007.

Q. Vohra and E. Chen, BGP Support for Four-octet AS Number Space, RFC 4893, May 2007.

V. Gill, J. Heasley, D. Meyer, P. Savola, and C. Pignatoro, The Generalized TTL Security Mechanism (GTSM), RFC 5082, October 2007.

J. Scudder and R. Chandra, Capabilities Advertisement with BGP-4, RFC 5492, February 2009.

E. Chen, J. Scudder, P. Mohapatra, and K. Patel, Revised Error Handling for BGP UPDATE Messages, RFC 7606, August 2015.

MRT routing information export format, draft-ietf-grow-mrt-17, August 2011.

J. Dong, M. Chen, and A. Suryanarayana, Subcodes for BGP Finite State Machine Error, RFC 6608, May 2012.

J. Heitz, J. Snijders, K. Patel, I. Bagdonas, and N. Hilliard, BGP Large Communities Attribute, RFC 8092, February 2017.

J. Snijders, J. Heitz, and J. Scudder, BGP Administrative Shutdown Communication, draft-ietf-idr-shutdown, January 2017.

The bgpd program first appeared in OpenBSD 3.5.

February 19, 2017 OpenBSD-6.1