Fast File System consistency check and
fsck_ffs performs interactive file system
consistency checks and repairs for each file system specified. It is
normally invoked from
The kernel takes care that only a restricted class of innocuous file system inconsistencies can happen unless hardware or software failures intervene. These are limited to the following:
- Unreferenced inodes
- Link counts in inodes too large
- Missing blocks in the free map
- Blocks in the free map also in files
- Counts in the super-block wrong
These are the only inconsistencies that
fsck_ffs with the
will correct; if it encounters other inconsistencies, it exits with an
abnormal return status and an automatic reboot will then fail. For each
corrected inconsistency, one or more lines will be printed identifying the
file system on which the correction will take place along with the nature of
the correction. After successfully correcting a file system,
fsck_ffs will print the number of files on that file
system, the number of used and free blocks, and the percentage of
If sent a
fsck_ffs will finish the file system checks, then
exit with an abnormal return status that causes an automatic reboot to fail.
This is useful when you want to finish the file system checks during an
automatic reboot, but do not want the machine to come up multiuser after the
If sent an
fsck_ffs will print a line to standard error
indicating the name of the device currently being checked, the current phase
number, and phase-specific progress information.
fsck_ffs audits and interactively repairs
inconsistent conditions for file systems. If the file system is
inconsistent, the operator is prompted for concurrence before each
correction is attempted. It should be noted that some of the corrective
actions which are not correctable under the
option will result in some loss of data. The amount and severity of data
lost may be determined from the diagnostic output. The default action for
each consistency correction is to wait for the operator to respond
“yes” or “no”. If the operator does not have
write permission on the file system,
default to a
fsck has more consistency
checks than its predecessors
The following flags are interpreted by
- Use the block# specified as the super block for the file system. Block 32 is usually an alternate super block.
- Convert the file system to the specified level. Note
that the level of a file system can only be raised. There are currently
four levels defined:
- The file system is in the old (static table) format.
- The file system is in the new (dynamic table) format.
- The file system supports 32-bit UIDs and GIDs, short symbolic links are stored in the inode, and directories have an added field showing the file type.
- If maxcontig is greater than one, build the free segment maps to aid in finding contiguous sets of blocks. If maxcontig is equal to one, delete any existing segment maps.
- Force checking of file systems. Normally, if a file system is cleanly
unmounted, the kernel will set a “clean flag” in the file
system superblock and
fsck_ffswill not check the file system. This option forces
fsck_ffsto check the file system, regardless of the state of the clean flag.
- Use the mode specified in octal as the permission bits to use when creating the lost+found directory rather than the default 1700. In particular, systems that wish to have lost files accessible by all users on the system should use a less restrictive set of permissions such as 755.
- Assume a “no” response to all questions asked by
fsck_ffsexcept for “CONTINUE?”, which is assumed to be affirmative. File systems will not be opened for writing. This is the default for file systems to be checked that are concurrently mounted writable.
- Enter preen mode:
fsck_ffswill check the file systems on the special (raw) devices listed on the command line and will make minor repairs without human intervention. Any major problems will cause
fsck_ffsto exit with a non-zero exit code, so as to alert any invoking program or script that human intervention is required.
- Assume a “yes” response to all questions asked by
fsck_ffs; this should be used with great caution as this is a free license to continue after essentially unlimited trouble has been encountered.
In interactive mode,
fsck_ffs will list
the conversion to be made and ask whether the conversion should be done. If
a negative answer is given, no further operations are done on the file
system. In preen mode, the conversion is listed and done if possible without
user interaction. Conversion in preen mode is best used when all the file
systems are being converted at once. The format of a file system can be
determined from the first line of output from
Inconsistencies checked are as follows:
- Blocks claimed more than once by inodes or the free map.
- Blocks claimed by an inode outside the range of the file system.
- Incorrect link counts.
- Size checks:
- Directory size not a multiple of
- Partially truncated file.
- Directory size not a multiple of
- Bad inode format.
- Blocks not accounted for anywhere.
- Directory checks:
- File pointing to unallocated inode.
- Inode number out of range.
- Dot or dot-dot not the first two entries of a directory or having the wrong inode number.
- Super Block checks:
- More blocks for inodes than there are in the file system.
- Bad free block map format.
- Total free block and/or free inode count incorrect.
Orphaned files and directories (allocated but unreferenced) are, with the operator's concurrence, reconnected by placing them in the lost+found directory. The name assigned is the inode number. If the lost+found directory does not exist, it is created. If there is insufficient space its size is increased.
Because of inconsistencies between the block device and the buffer cache, the raw device should always be used.
The diagnostics produced by
fully enumerated and explained in Appendix A of
Fsck_ffs - The UNIX File System Check
fs(5), fstab(5), fsck(8), fsdb(8), growfs(8), mount_ffs(8), newfs(8), rc(8)